Qlogic SANbox2-8c Guia de Instalação Página 39
- Página / 162
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
59042-01 A 4-1
Section 4
Installation
This section describes how to install and configure the SANbox2-8c switch. It also
describes how to load new firmware and how to recover a disabled switch.
4.1
Site Requirements
The following items are required for the installation of a SANbox2-8c switch:
■ Fabric management workstation
■ Power requirements
■ Environmental conditions
4.1.1
Fabric Management Workstation
SANbox Manager requires a management workstation equipped as described in
Table 4-1:
Telnet workstations require an RJ-45 Ethernet port and an operating system with
a Telnet client.
4.1.2
Switch Power Requirements
Operating voltage requirements are as follows:
90 to 137 Vac; 47 to 63 Hz
180 to 264 Vac; 47 to 63 Hz
Table 4-1. Management Workstation Requirements
Operating System
■ Windows® NT, 2000, 95/98
■ Linux® 6.2 Red Hat®
■ Solaris™
Memory 128 MB or more
Disk Space 150 MB per installation
Processor 300 MHz or faster
Hardware CD-ROM drive, RS-232 serial port, RJ-45 Ethernet port
Internet Browser Microsoft® Internet Explorer® or Netscape Navigator®
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 4
- 59042-01 A Page v 5
- Appendix A Specifications 6
- Page viii 59042-01 A 8
- Introduction 9
- Related Materials 10
- Safety Notices 11
- Sicherheitshinweise 11
- Communications Statements 12
- Statement 12
- CE Statement 13
- VCCI Class A Statement 14
- BSMI Class A Statement 14
- Laser Safety Information 15
- Accessible Parts 15
- Pièces Accessibles 15
- Zugängliche Teile 15
- Technical Support 16
- Availability 16
- Training 16
- Contact Information 16
- General Description 17
- Chassis Controls and LEDs 18
- Reset/Force PROM Button 18
- Resetting a Switch 19
- Over Temperature LED (Yellow) 19
- Fan Fail LED (Yellow) 19
- Heartbeat LED (Yellow) 20
- Input Power LED (Green) 20
- Fibre Channel Ports 20
- Logged-In LED 21
- Activity LED 21
- Port Modes 22
- Fabric Ports 22
- Translated Loop Port 23
- Expansion Port 23
- Ethernet Port 24
- Serial Port 25
- Power Supply and Fan 26
- Switch Management 26
- Planning 27
- Multiple Chassis Fabrics 28
- Common Topologies 29
- Cascade Topology 29
- Mesh Topology 30
- Multistage Topology 31
- Performance 32
- Distance 32
- Bandwidth 33
- Device Access 34
- Soft Zones 35
- Fabric Management 36
- Fabric Security 37
- 3 – Planning 38
- 3-12 59042-01 A 38
- Installation 39
- Environmental Conditions 40
- Installing a Switch 40
- Mount the Switch 41
- Install SFP Transceivers 42
- 4 – Installation 43
- 59042-01 A 4-5 43
- 4-6 59042-01 A 44
- SANbox2 Login: admin 46
- Password: ******** 46
- Install SANbox Manager 47
- 4-10 59042-01 A 48
- ./sansurfer_linux_install.bin 49
- 4-12 59042-01 A 50
- Configure the Switch 51
- Configure the Ports 52
- Cable Devices to the Switch 52
- Installing Firmware 52
- 59042-01 A 4-15 53
- 4-16 59042-01 A 54
- Powering Down a Switch 55
- 4-18 59042-01 A 56
- Diagnostics/Troubleshooting 57
- Force PROM Mode Pattern 58
- Fatal Error Blink Pattern 58
- POST Diagnostics 59
- 59042-01 A 5-3 59
- 5-4 59042-01 A 60
- Logged-In LED Indications 61
- Chassis Diagnostics 63
- Fan Fail LED is Illuminated 64
- Recovering a Switch 65
- Force PROM – Exit 66
- Force PROM – Image Unpack 66
- Force PROM – Copy Log Files 67
- Force PROM – Reset Switch 67
- 5-12 59042-01 A 68
- Specifications 69
- Switch Maintainability 70
- Switch Dimensions 71
- Switch Electrical 71
- Switch Environmental 71
- A – Specifications 72
- A-4 59042-01 A 72
- 59042-01 A A-5 73
- A-6 59042-01 A 74
- /> telnet 123.45.67.890 75
- Command Syntax 76
- Commands 77
- Admin Command 78
- Alias Command 79
- B-6 59042-01 A 80
- Config Command 81
- B-8 59042-01 A 82
- SANbox2 $> date 83
- Tue Nov 12 07:51:24 2002 83
- SANbox2 #> admin start 84
- SANbox2 $> admin end 84
- Help Command 85
- History Command 86
- Image Command 87
- SANbox2 (admin) #> lip 2 88
- Passwd Command 89
- Ps Command 90
- Quit Command 91
- Reset Command 92
- Set Command 97
- SANbox2 $> set beacon on 98
- Command succeeded 98
- SANbox2 $> set beacon off 98
- B – Command Line Interface 104
- Set Config Command 104
- B-30 59042-01 A 104
- 59042-01 A B-31 105
- B-32 59042-01 A 106
- Set Log Command 107
- B-34 59042-01 A 108
- 59042-01 A B-35 109
- Set Port Command 110
- Set Setup Command 111
- 59042-01 A B-39 113
- B-40 59042-01 A 114
- Show Command 115
- B-42 59042-01 A 116
- B-46 59042-01 A 120
- 59042-01 A B-47 121
- B-48 59042-01 A 122
- 59042-01 A B-49 123
- B-50 59042-01 A 124
- Show Config Command 125
- B-52 59042-01 A 126
- 59042-01 A B-53 127
- SANbox2 $> show log level 128
- Show Log Command 129
- 59042-01 A B-55 129
- Show Perf Command 130
- 59042-01 A B-57 131
- Show Setup Command 132
- 59042-01 A B-59 133
- Shutdown Command 134
- Test Command 135
- B-62 59042-01 A 136
- 59042-01 A B-63 137
- SANbox2 $> uptime 138
- User Command 139
- B-66 59042-01 A 140
- SANbox2 $> whoami 141
- User name:admin@session2 141
- Switch name:SANbox2 141
- Switch domain ID:1 141
- Zone Command 142
- ■ Alias name 143
- B-70 59042-01 A 144
- zone_set_1 145
- Zoneset Command 146
- 59042-01 A B-73 147
- B-74 59042-01 A 148
- Zoning Command 149
- B-76 59042-01 A 150
- 59042-01 A B-77 151
- B-78 59042-01 A 152
- Glossary 153
- Glossary-2 59042-01 A 154
- 59042-01 A Glossary-3 155
- Glossary-4 59042-01 A 156
- 59042-01 A Index-1 157
- Index-2 59042-01 A 158
- 59042-01 A Index-3 159
- Index-4 59042-01 A 160
- 59042-01 A Index-5 161
- Index-6 59042-01 A 162
Manuais e produtos relacionados com Comutadores de rede Qlogic SANbox2-8c
(130 páginas)
(42 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais