Qlogic SANbox 9000 Series Guia de Instalação

59229-05 AQLogic 9000 SeriesStackable Chassis SwitchInstallation GuideFirmware Version 7.8

PrefaceRelated Materialsx 59229-05 ARelated MaterialsThe following manuals and materials are referenced in the text and/or provide additional informa

4–Diagnostics/TroubleshootingCPU Blade Diagnostics4-6 59229-05 ACPU Blade DiagnosticsFigure 4-1 illustrates the CPU blade diagnostic process. If the

4–Diagnostics/TroubleshootingI/O Blade Diagnostics59229-05 A 4-7I/O Blade DiagnosticsFigure 4-2 illustrates the I/O blade diagnostic process. For por

4–Diagnostics/TroubleshootingFC Port Diagnostics4-8 59229-05 AFC Port DiagnosticsPort diagnostics for each port are indicated by the Logged-In LED. T

4–Diagnostics/TroubleshootingFC Port Diagnostics59229-05 A 4-9E_Port IsolationA Logged-In LED error indication is often the result of E_Port isolatio

4–Diagnostics/TroubleshootingFC Port Diagnostics4-10 59229-05 A4. Compare the RA_TOV and ED_TOV timeout values for all switches in the fabric using t

4–Diagnostics/TroubleshootingFC Port Diagnostics59229-05 A 4-11If the count for any of these errors exceeds the rising trigger for three consecutive

4–Diagnostics/TroubleshootingTransceiver Diagnostics4-12 59229-05 ATransceiver DiagnosticsYou can display the following transceiver information using

4–Diagnostics/TroubleshootingPower Supply Blade Diagnostics59229-05 A 4-13Power Supply Blade DiagnosticsFigure 4-4 illustrates the Power Supply blade

4–Diagnostics/TroubleshootingFan Blade Diagnostics4-14 59229-05 AFan Blade DiagnosticsFigure 4-5 illustrates the Fan blade diagnostic process. If the

4–Diagnostics/TroubleshootingRecovering a Switch Using Maintenance Mode59229-05 A 4-15Recovering a Switch Using Maintenance ModeA switch can become i

PrefaceSafety Notices59229-05 A xiSafety NoticesA Warning notice indicates the presence of a hazard that has the potential of causing personal injury

4–Diagnostics/TroubleshootingRecovering a Switch Using Maintenance Mode4-16 59229-05 A5. The maintenance menu displays several recovery options. To s

4–Diagnostics/TroubleshootingRecovering a Switch Using Maintenance Mode59229-05 A 4-176. Enter the maintenance mode account name and password (prom,

4–Diagnostics/TroubleshootingRecovering a Switch Using Maintenance Mode4-18 59229-05 ARemaking the File SystemIn the event of sudden loss of power, i

59229-05 A 5-15 Customer Replaceable UnitsThis section describes the removal and installation procedures for the following Customer Replaceable Units

5–Customer Replaceable Units5-2 59229-05 AFigure 5-1 QLogic 9000 Series Customer Replaceable UnitsCAUTION!To prevent overheating, all blades and bla

5–Customer Replaceable UnitsReplacing Transceivers and Stacking Cables59229-05 A 5-3Replacing Transceivers and Stacking CablesThe transceivers and st

5–Customer Replaceable UnitsReplacing CPU Blades5-4 59229-05 AReplacing CPU BladesThe following replacement procedures assume the use of the CLI. Ref

5–Customer Replaceable UnitsReplacing CPU Blades59229-05 A 5-5The CPU blade replacement process depends on the following factors: Licensing: standar

5–Customer Replaceable UnitsReplacing CPU Blades5-6 59229-05 AStandard Single CPU – Primary CPU Blade ReplacementFor a standard, single CPU blade swi

5–Customer Replaceable UnitsReplacing CPU Blades59229-05 A 5-7Figure 5-2 Removing the CPU0 Blade8. Install the new CPU blade. Remove protective cove

PrefaceCommunications Statementsxii 59229-05 ACommunications StatementsThe following statements apply to this product. The statements for other produ

5–Customer Replaceable UnitsReplacing CPU Blades5-8 59229-05 A14. Load the image file on the switch. Move to the directory that contains the firmware

5–Customer Replaceable UnitsReplacing CPU Blades59229-05 A 5-917. Restore the switch configuration. Log in to the switch again and open a Telnet sess

5–Customer Replaceable UnitsReplacing CPU Blades5-10 59229-05 A5. Observe the new primary CPU blade Heartbeat LED. It should blink once per second. I

5–Customer Replaceable UnitsReplacing CPU Blades59229-05 A 5-114. Install the new CPU blade. Remove protective coverings from the backplane connector

5–Customer Replaceable UnitsReplacing I/O Blades5-12 59229-05 AReplacing I/O BladesYou can remove and install I/O blades while the switch is operatin

5–Customer Replaceable UnitsReplacing I/O Blades59229-05 A 5-13Removing an I/O Blade

5–Customer Replaceable UnitsReplacing I/O Blades5-14 59229-05 ATo remove an I/O blade, do the following:1. Label and disconnect the Fibre Channel por

5–Customer Replaceable UnitsReplacing I/O Blades59229-05 A 5-15Installing an I/O BladeTo install an I/O blade, do the following:1. Open the I/O blade

5–Customer Replaceable UnitsReplacing Power Supply Blades5-16 59229-05 AReplacing Power Supply BladesYou can remove or install one of the two functio

5–Customer Replaceable UnitsReplacing Power Supply Blades59229-05 A 5-17CAUTION!Always use an ESD wrist strap when removing and installing a Power Su

PrefaceCommunications Statements59229-05 A xiiiCE StatementThe CE symbol on the equipment indicates that this system complies with the EMC (Electroma

5–Customer Replaceable UnitsReplacing Power Supply Blades5-18 59229-05 A

5–Customer Replaceable UnitsReplacing Power Supply Blades59229-05 A 5-19Removing a Power Supply BladeTo remove a power supply blade, do the following

5–Customer Replaceable UnitsReplacing Power Supply Blades5-20 59229-05 AInstalling a Power Supply BladeTo install a Power Supply blade, do the follow

5–Customer Replaceable UnitsReplacing Fan Blades59229-05 A 5-21Replacing Fan BladesYou can remove or install one of the Fan blades while the switch i

5–Customer Replaceable UnitsReplacing Fan Blades5-22 59229-05 AATTENTION!Portez toujours un bracelet antistatique lors du retrait et de l'instal

5–Customer Replaceable UnitsReplacing Fan Blades59229-05 A 5-23Removing a Fan BladeTo remove a Fan blade, rotate the latch to the full open position.

5–Customer Replaceable UnitsReplacing Fan Blades5-24 59229-05 ANotes

59229-05 A A-1A SpecificationsThis appendix contains the specifications for the QLogic 9000 Series switch. Refer to Section 1 for the location of all

A–SpecificationsFabric SpecificationsA-2 59229-05 AFabric SpecificationsOptional License KeysTable A-1. Fabric SpecificationsFibre Channel Protocols.

A–SpecificationsPerformance Features59229-05 A A-3Performance FeaturesFault Tolerant... Supports automatic and manual

PrefaceLaser Safety Informationxiv 59229-05 AVCCI Class A StatementThis is a Class A product based on the standard of the Voluntary Control Council F

A–SpecificationsPerformance FeaturesA-4 59229-05 APer Port Buffering... ASIC-embedded memory (non-shared). Each port has a

A–SpecificationsModular Scalability59229-05 A A-5Modular ScalabilityTable A-4. Modular Scalability Ports per Chassis... 16 t

A–SpecificationsModular ScalabilityA-6 59229-05 AMedia Type (ordered separately) 8-Gbps I/O blade... 4-Gbps I/O blade...

A–SpecificationsInteroperability/Certifications59229-05 A A-7Interoperability/CertificationsFabric ServicesTable A-5. Interoperability/Certifications

A–SpecificationsFabric ServicesA-8 59229-05 AManagement Methods... Enterprise Fabric Suite 2007 Graphical User Interface (GUI) Qui

A–SpecificationsMaintainability59229-05 A A-9MaintainabilityTable A-7. Maintainability Maintenance Strategy... Customer Replaceable

A–SpecificationsPhysical CharacteristicsA-10 59229-05 APhysical CharacteristicsVisual User Interface ... LED indicators on the Mai

A–SpecificationsPhysical Characteristics59229-05 A A-11

A–SpecificationsElectrical RequirementsA-12 59229-05 AElectrical Requirements

A–SpecificationsPower Cord Specifications59229-05 A A-13Power Cord SpecificationsThe switch comes with two power cords with NEMA 5-15 non-locking plu

PrefaceAccessible Parts59229-05 A xvAccessible PartsThe Customer Replaceable Units (CRU) in the QLogic 9000 Series Stackable Chassis Switch are the f

A–SpecificationsEnvironmental FactorsA-14 59229-05 AEnvironmental FactorsNorway CEE 7/7 Plug CPK-9000-CEERussia CEE 7/7 Plug CPK-9000-CEESingapore/Br

A–SpecificationsRegulatory Certifications59229-05 A A-15Regulatory CertificationsTable A-12. Regulatory Certifications Safety Standards...

A–SpecificationsRegulatory CertificationsA-16 59229-05 ANotes

59229-05 A Glossary-1GlossaryActive Zone SetThe zone set that defines the current zoning for the fabric.Active FirmwareThe firmware image on the swit

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideGlossary-2 59229-05 AClass 2 ServiceA service which multiplexes frames at frame boundar

59229-05 A Glossary-3QLogic 9000 Series Stackable Chassis SwitchInstallation GuideFault TolerantA licensed feature that supports automatic and manua

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideGlossary-4 59229-05 AManagement WorkstationPC workstation that manages the fabric throu

59229-05 A Glossary-5QLogic 9000 Series Stackable Chassis SwitchInstallation GuideStorage Management Initiative–SpecificationA standard that provide

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideGlossary-6 59229-05 ANotes

59229-05 A Index-1IndexAaccount namefactory 3-20maintenance mode 4-15active zone set 2-2Activity LED 1-12Ethernet port 1-12Fibre Channel port 1-6adap

PrefaceLicense Agreementsxvi 59229-05 ALicense AgreementsRefer to the QLogic Software End User License Agreement for a complete listing of all licens

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideIndex-2 59229-05 ACPU Good LED 1-10CPU Hotwsap LED 1-10CPU Power LED 1-10CPU Primary LE

59229-05 A Index-3QLogic 9000 Series Stackable Chassis SwitchInstallation GuideFault LEDchassis 1-3CPU 1-10Fan 1-15I/O blade 1-6Power Supply 1-14Fau

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideIndex-4 59229-05 ALEDActivity 1-6, 1-12chassis Beacon 1-3chassis Fault 1-3chassis Good

59229-05 A Index-5QLogic 9000 Series Stackable Chassis SwitchInstallation Guideportbinding 2-13, A-5buffer credits 2-3cover 3-12errors 4-10Fibre Cha

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideIndex-6 59229-05 ASimple Network Management Protocoldescription 1-18service 2-10site re

59229-05 A Index-7QLogic 9000 Series Stackable Chassis SwitchInstallation Guidezone setactive 2-2definition 2-2zoningdatabase 2-2hardware enforced 2

QLogic 9000 Series Stackable Chassis SwitchInstallation GuideIndex-8 59229-05 ANotes

© 2009 QLogic Corporation. Specifications are subject to change without notice. All rights reserved worldwide. QLogic, the QLogic logo, Enterprise Fab

PrefaceTechnical Support59229-05 A xviiTechnical SupportCustomers should contact their authorized maintenance provider for technical support of their

PrefaceTechnical Supportxviii 59229-05 ANotes

59229-05 A 1-11 General DescriptionThis section describes the features and capabilities of the QLogic 9000 Series Stackable Chassis Switch. The follo

ii 59229-05 AQLogic 9000 Series Stackable Chassis SwitchInstallation GuideInformation furnished in this manual is believed to be accurate and reliabl

1–General DescriptionHardware Overview1-2 59229-05 AI/O blades are ordered separately so that you can specify how many I/O blades you want and what t

1–General DescriptionMaintenance Panel59229-05 A 1-3I/O blades (IO0–IO7), CPU blades (CPU0, CPU1), Power Supply blades (PS0, PS1), and the Fan blades

1–General DescriptionI/O Blades1-4 59229-05 AInitially, the alternate Ethernet ports are inactive, thus requiring that you make the Ethernet connecti

1–General DescriptionI/O Blades59229-05 A 1-5Fibre Channel ports are numbered based on the blade ID as shown in Figure 1-3. For example, for I/O blad

1–General DescriptionI/O Blades1-6 59229-05 AI/O Blade LEDsThe I/O blade LEDs are as follows: I/O Blade Good LED (Green)–This LED illuminates to ind

1–General DescriptionI/O Blades59229-05 A 1-7Port TypesThe switch supports generic ports (G_Port, GL_Port), fabric ports (F_Port, FL_Port), and expan

1–General DescriptionI/O Blades1-8 59229-05 ATransceivers and 10-Gbps Stacking CablesSFP and X2 transceivers convert electrical signals to and from o

1–General DescriptionCPU Blades59229-05 A 1-9CPU BladesThe CPU blade, shown in Figure 1-4, provides configuration, monitoring, data path management,

1–General DescriptionCPU Blades1-10 59229-05 ACPU Blade LEDsThe CPU blade LEDs indicated the operating condition of the CPU blade. The CPU Good LED,

1–General DescriptionCPU Blades59229-05 A 1-11Maintenance ButtonThe Maintenance button is a dual-function momentary switch on the CPU blade. Its purp

59229-05 A iiiTable of ContentsPrefaceIntended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ixRel

1–General DescriptionCPU Blades1-12 59229-05 AEthernet PortEach CPU blade has an Ethernet port and a serial port.The Ethernet port is an RJ-45 connec

1–General DescriptionPower Supply Blades59229-05 A 1-13Serial PortThe serial port is an RJ-45 connector and uses a 10/100 Base-T Ethernet straight ca

1–General DescriptionPower Supply Blades1-14 59229-05 AEach Power Supply blade has an AC power receptacle, an On/Off switch, and a set of LEDs as sho

1–General DescriptionFan Blades59229-05 A 1-15Fan BladesThe switch is equipped with two Fan blades that cool the switch. Both Fan blades must be inst

1–General DescriptionFabric and Switch Management1-16 59229-05 AFabric and Switch ManagementThe switch supports the following management tools: Ente

1–General DescriptionFabric and Switch Management59229-05 A 1-17QuickToolsTo provide basic fabric management tools in a graphical user interface and

1–General DescriptionFabric and Switch Management1-18 59229-05 ACommand Line InterfaceThe command line interface (CLI) provides monitoring and config

59229-05 A 2-12 PlanningConsider the following when planning a fabric: Devices Device Access Performance Feature Licensing Multiple Chassis Fabr

2–PlanningDevice Access2-2 59229-05 ADevice AccessConsider device access needs within the fabric. Access is controlled by the use of zones and zone s

2–PlanningPerformance59229-05 A 2-3PerformanceThe QLogic 9000 Series switch supports class 2 and class 3 Fibre Channel service at transmission rates

iv 59229-05 AQLogic 9000 Series Stackable Chassis SwitchInstallation GuideTransceivers and 10-Gbps Stacking Cables . . . . . . . . . . . . . . . . .

2–PlanningPerformance2-4 59229-05 ARegardless of how many credits are borrowed, extending credits requires a minimum cable length that is dependent o

2–PlanningFeature Licensing59229-05 A 2-5LatencyLatency is a measure of how fast a frame travels from one port to another. The factors that affect la

2–PlanningMultiple Chassis Fabrics2-6 59229-05 AMultiple Chassis FabricsBy connecting switches together you can expand the number of available ports

2–PlanningMultiple Chassis Fabrics59229-05 A 2-7Optimizing Device PerformanceWhen choosing a topology for a multiple chassis fabric, you should also

2–PlanningMultiple Chassis Fabrics2-8 59229-05 ADomain ID, Principal Priority, and Domain ID LockThe following switch configuration settings affect m

2–PlanningMultiple Chassis Fabrics59229-05 A 2-9Interconnecting QLogic 9000 Series SwitchesThere are three ways to interconnect QLogic 9000 Series sw

2–PlanningSwitch Services2-10 59229-05 ASwitch ServicesYou can configure your switch to suit the demands of your environment by enabling or disabling

2–PlanningSwitch Services59229-05 A 2-11 Common Information Model (CIM): Provides for the management of the switch through third-party applications

2–PlanningInternet Protocol Support2-12 59229-05 AInternet Protocol SupportThe switch supports IP version 4, IP version 6, and Domain Name System (DN

2–PlanningSecurity59229-05 A 2-13IP SecurityIP Security provides encryption-based security for IP version 4 and IP version 6 communications through t

59229-05 A vQLogic 9000 Series Stackable Chassis SwitchInstallation GuideDevice Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–PlanningSecurity2-14 59229-05 AConsider your requirements for connection security: for the command line interface (SSH), management applications su

2–PlanningSecurity59229-05 A 2-15Consider the devices, switches, and management agents and evaluate the need for authorization and authentication. Al

2–PlanningSecurity2-16 59229-05 A1. Create a security set (Security_Set_1) on Switch_1.a. Create a port group (Group_Port_1) in Security_Set_1 with S

2–PlanningSecurity59229-05 A 2-17b. Create an ISL group (Group_ISL_1) in Security_Set_1 with Switch_1 and Switch_2 as members. The Switch_1 secret mu

2–PlanningSecurity2-18 59229-05 ASecurity Example: RADIUS ServerConsider the fabric shown in Figure 2-3. This fabric is similar to the one shown in F

2–PlanningSecurity59229-05 A 2-191. Configure the Radius_1 host as a RADIUS server on Switch_1 and Switch_2 to authenticate device logins. Specify th

2–PlanningSecurity2-20 59229-05 A2. Create a security set (Security_Set_1) on Switch_1.a. Create a port group (Group_Port_1) in Security_Set_1 with S

2–PlanningSecurity59229-05 A 2-21b. Create an ISL group (Group_ISL_1) in Security_Set_1 with Switch_1 and Switch_2 as members. The Switch_1 secret mu

2–PlanningSecurity2-22 59229-05 ASecurity Example: Host AuthenticationConsider the fabric shown in Figure 2-4. In this fabric, only Switch_2 and HBA_

2–PlanningSecurity59229-05 A 2-231. Create a security set (Security_Set_2) on Switch_2.2. Create a Management Server group (Group_1) in Security_Set_

vi 59229-05 AQLogic 9000 Series Stackable Chassis SwitchInstallation GuideFatal POST Error Blink Pattern . . . . . . . . . . . . . . . . . . . . . .

2–PlanningFabric Management2-24 59229-05 AFabric ManagementThe Enterprise Fabric Suite 2007 application executes on a management workstation that pro

59229-05 A 3-13 InstallationThis section describes how to install and configure the QLogic 9000 Series switch. The following topics are covered: Sit

3–InstallationSite Requirements3-2 59229-05 AFabric Management WorkstationThe requirements for fabric management workstations running Enterprise Fabr

3–InstallationInstalling a Switch59229-05 A 3-3Installing a SwitchUnpack the switch and accessories. The QLogic 9000 Series switch is shipped with th

3–InstallationInstalling a Switch3-4 59229-05 AInstalling a QLogic 9000 Series switch involves the following steps:1. Mount the Switch2. Stack the Sw

3–InstallationInstalling a Switch59229-05 A 3-5Mount the SwitchWARNING!!Mount switches in the rack so that the weight is distributed evenly. An uneve

3–InstallationInstalling a Switch3-6 59229-05 AATTENTION! Si le commutateur est monté dans un assemblage fermé ou dans un bâti à plusieurs unités, v

3–InstallationInstalling a Switch59229-05 A 3-7 ¡PRECAUC

3–InstallationInstalling a Switch3-8 59229-05 AThe switch is designed to be mounted in a rack using the mounting brackets and the QLogic 9000 Series

3–InstallationInstalling a Switch59229-05 A 3-91. Install left (1) and right (2) switch rails on the switch using six 8-32 screws (3) for each. Be su

59229-05 A viiQLogic 9000 Series Stackable Chassis SwitchInstallation GuidePerformance Features . . . . . . . . . . . . . . . . . . . . . . . . . .

3–InstallationInstalling a Switch3-10 59229-05 AInstall I/O BladesI/O blades are ordered and shipped separately so that you can customize your switch

3–InstallationInstalling a Switch59229-05 A 3-11Stack the Switches10-Gbps stacking cables are available to connect two QLogic 9000 Series switches or

3–InstallationInstalling a Switch3-12 59229-05 AInstall TransceiversThe switch supports a variety of SFP and X2 transceivers. To install a transceive

3–InstallationInstalling a Switch59229-05 A 3-13Power Up the SwitchWARNING!!This product is supplied with a 3-wire power cable and plug for the user’

3–InstallationInstalling a Switch3-14 59229-05 A WARNUNG

3–InstallationInstalling a Switch59229-05 A 3-15The switch comes with two NEMA 5-15, non-locking, power cords (SKU: CPK-9000-US). This power cord is

3–InstallationInstalling a Switch3-16 59229-05 AConfigure the WorkstationIf you plan to use the command line interface to configure and manage the sw

3–InstallationInstalling a Switch59229-05 A 3-17Configuring the Workstation Serial PortTo configure the workstation serial port, do the following:1.

3–InstallationInstalling a Switch3-18 59229-05 A For Solaris: Modify the /etc/remote file and locate the hardwire entry. Choose the :dv=/dev/term/ s

3–InstallationInstalling a Switch59229-05 A 3-19Start Enterprise Fabric Suite 2007To start Enterprise Fabric Suite 2007, do the following.1. Start th

viii 59229-05 AQLogic 9000 Series Stackable Chassis SwitchInstallation Guide5-5 Removing a Fan Blade. . . . . . . . . . . . . . . . . . . . . . . . .

3–InstallationInstalling a Switch3-20 59229-05 AConfigure the SwitchYou can configure the switch using the Enterprise Fabric Suite 2007 application,

3–InstallationInstalling a Switch59229-05 A 3-21 Serial – Windows: Open the HyperTerminal application on a Windows platform.a. Choose the Start butt

3–InstallationInstalling Firmware3-22 59229-05 AInstalling FirmwareThe switch comes with current firmware installed. You can upgrade the firmware fro

3–InstallationInstalling Firmware59229-05 A 3-23Using Enterprise Fabric Suite 2007 to Install FirmwareTo install firmware using Enterprise Fabric Sui

3–InstallationInstalling Firmware3-24 59229-05 AUsing the CLI to Install FirmwareThe method you choose to install firmware using the CLI depends on t

3–InstallationInstalling Firmware59229-05 A 3-25To install firmware using the CLI when a File Transfer Protocol (FTP) server is present on the manage

3–InstallationInstalling Firmware3-26 59229-05 ACustom Firmware InstallationA custom firmware installation downloads the firmware image file from an

3–InstallationAdding a Switch to an Existing Fabric59229-05 A 3-27Adding a Switch to an Existing FabricIf there are no special conditions to be confi

3–InstallationInstalling Feature License Keys3-28 59229-05 AInstalling Feature License KeysRefer to “Feature Licensing” on page 2-5 for information a

3–InstallationHyperStacking59229-05 A 3-29HyperStackingHyperStacking connects two Model 9200 switches through the ICC ports on the two pairs of CPU b

59229-05 A ixPrefaceThis manual describes the features and installation of the QLogic 9000 Series Stackable Chassis Switch, firmware version 7.8. Thi

3–InstallationHyperStacking3-30 59229-05 A5. Use a screwdriver to remove the covers from all ICC ports. Connect a HyperStack cable to one of the ICC

3–InstallationHyperStacking59229-05 A 3-317. Secure the HyperStack cables in place using ties wraps as shown in Figure 3-8. Secure the outer cables t

3–InstallationHyperStacking3-32 59229-05 A10. Enter the Show Fabric CLI command to confirm that both QLogic 9000 Series switches are in the fabric.SA

3–InstallationHyperStacking59229-05 A 3-33

3–InstallationHyperStacking3-34 59229-05 ANotes

59229-05 A 4-14 Diagnostics/TroubleshootingThis section describes how to recognize, diagnose, and correct problems. Diagnostic information about the

4–Diagnostics/TroubleshootingPower-On Self Test4-2 59229-05 APower-On Self TestThe switch performs a Power-On Self Test (POST) as part of its power-u

4–Diagnostics/TroubleshootingError Code Blink Patterns59229-05 A 4-3Internal Firmware Failure Blink PatternAn internal firmware failure blink pattern

4–Diagnostics/TroubleshootingError Code Blink Patterns4-4 59229-05 AConfiguration File System Error Blink PatternA configuration file system error bl

4–Diagnostics/TroubleshootingError Code Blink Patterns59229-05 A 4-5c. Open an admin session to acquire the necessary authority.QLogic $>admin sta