Qlogic SANbox 5602 Guia de Instalação Página 46
- Página / 228
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
3 – Planning
Multiple Chassis Fabrics
3-8 59096-00 A
0
3.5.2
Domain ID, Principal Priority, and Domain ID Lock
The following switch configuration settings affect multiple chassis fabrics:
Domain ID
Principal priority
Domain ID lock
The domain ID is a unique number from 1–239 that identifies each switch in a
fabric. The principal priority is a number (1–255) that determines the principal
switch which manages domain ID assignments for the fabric. The switch with the
highest principal priority (1 is high, 255 is low) becomes the principal switch. If the
principal priority is the same for all switches in a fabric, the switch with the lowest
WWN becomes the principal switch.
The domain ID lock allows (False) or prevents (True) the reassignment of the
domain ID on that switch. Switches come from the factory with the domain ID set
to 1, the domain ID lock set to False, and the principal priority set to 254. Refer to
the SANbox 5602 Switch Management User’s Guide for information about
changing the domain ID and domain ID lock using SANsurfer Switch Manager.
Refer to the “Set Config Command” on page B-39 for information about changing
the default domain ID, domain ID lock, and principal priority parameters.
An unresolved domain ID conflict means that the switch with the higher WWN will
isolate as a separate fabric, and the Logged-In LEDs on both switches will flash
green to show the affected ports. If you connect a new switch to an existing fabric
with its domain ID unlocked, and a domain ID conflict occurs, the new switch will
isolate as a separate fabric. However, you can remedy this by resetting the new
switch or taking it offline then back online. The principal switch will reassign the
domain ID and the switch will join the fabric.
Note: Domain ID reassignment is not reflected in zoning that is defined by
domain ID/port number pair or Fibre Channel address. You must
reconfigure zones that are affected by domain ID reassignment. To
prevent zoning definitions from becoming invalid under these
conditions, lock the domain IDs using SANsurfer Switch Manager or
the Set Config Switch command.
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 5
- Section 6 Removal/Replacment 6
- Appendix A Specifications 6
- 59096-00 A Page vii 7
- 59096-00 A Page ix 9
- Page x 59096-00 A 10
- Introduction 11
- Related Materials 12
- Safety Notices 13
- Sicherheitshinweise 13
- Communications Statements 14
- Statement 14
- CE Statement 15
- VCCI Class A Statement 16
- Laser Safety Information 16
- Accessible Parts 17
- Pièces Accessibles 17
- Zugängliche Teile 17
- General Public License 18
- Preamble 18
- 1 – Introduction 19
- 59096-00 A 1-9 19
- 1-10 59096-00 A 20
- 59096-00 A 1-11 21
- 1-12 59096-00 A 22
- 59096-00 A 1-13 23
- 1-14 59096-00 A 24
- Technical Support 25
- Availability 25
- Training 25
- Contact Information 25
- 1-16 59096-00 A 26
- General Description 27
- Chassis Controls and LEDs 28
- Maintenance Button 28
- Resetting a Switch 28
- Chassis LEDs 29
- Input Power LED (Green) 30
- Heartbeat LED (Green) 30
- System Fault LED (Amber) 30
- Fibre Channel Ports 31
- Port LEDs 32
- Port Logged-In LED (Green) 32
- Port Activity LED (Green) 32
- Transceivers 33
- Port Types 33
- Ethernet Port 34
- Serial Port 35
- Power Supplies and Fans 36
- Switch Management 37
- SANsurfer Switch Manager 37
- File Transfer Protocol 38
- Planning 39
- Device Access 40
- Soft Zones 41
- Performance 42
- Distance 42
- Bandwidth 43
- Port Licensing 44
- Multiple Chassis Fabrics 44
- Optimizing Device Performance 45
- 3 – Planning 46
- 3-8 59096-00 A 46
- Stacking 47
- 3-10 59096-00 A 48
- Common Topologies 49
- Cascade Topology 49
- Mesh Topology 50
- Multistage Topology 51
- Fabric Security 52
- User Account Security 52
- Fabric Services 52
- 3-16 59096-00 A 54
- Installation 55
- Environmental Conditions 56
- Installing a Switch 56
- Mount the Switch 57
- Install Transceivers 58
- Configure the Workstation 61
- SANsurfer Management Suite 65
- SMS Installation for Windows 65
- 4 – Installation 66
- 4-12 59096-00 A 66
- SMS Installation for Linux 67
- SMS Installation for Solaris 69
- 4-18 59096-00 A 72
- 59096-00 A 4-19 73
- Configure the Switch 74
- Cable Devices to the Switch 76
- Install Firmware 76
- Powering Down a Switch 79
- 4-26 59096-00 A 80
- Diagnostics/Troubleshooting 81
- Chassis Diagnostics 82
- 5-2 59096-00 A 82
- Heartbeat LED Blink Patterns 83
- System Error Blink Pattern 84
- Logged-In LED Indications 87
- E_Port Isolation 88
- Excessive Port Errors 89
- 5-10 59096-00 A 90
- Power Supply Diagnostics 91
- Recovering a Switch 91
- Maintenance – Exit 93
- Maintenance – Image Unpack 93
- 5-14 59096-00 A 94
- Removal/Replacment 95
- 6 – Removal/Replacment 96
- 6-2 59096-00 A 96
- 6-4 59096-00 A 98
- Specifications 99
- Maintainability 101
- Fabric Management 101
- Dimensions 101
- Electrical 102
- Environmental 102
- Regulatory Certifications 103
- A-6 59096-00 A 104
- A – Specifications 104
- Command Line Interface 105
- User Accounts 106
- Modifying a Configuration 107
- Commands 111
- Admin Command 113
- Alias Command 114
- B – Command Line Interface 115
- 59096-00 A B-11 115
- Config Command 116
- 59096-00 A B-13 117
- B-14 59096-00 A 118
- Create Support Command 119
- B-16 59096-00 A 120
- Date Command 121
- Feature Command 122
- Firmware Install Command 123
- Hardreset Command 124
- Help Command 125
- History Command 126
- Hotreset Command 127
- Image Command 128
- B-26 59096-00 A 130
- SANbox (admin) $>hotreset 130
- Lip Command 131
- Passwd Command 132
- Ping Command 133
- Ps Command 134
- Quit Command 135
- Reset Command 136
- Set Command 141
- B-38 59096-00 A 142
- Set Config Command 143
- 59096-00 A B-47 151
- B-48 59096-00 A 152
- 59096-00 A B-49 153
- B-50 59096-00 A 154
- 59096-00 A B-51 155
- Set Log Command 156
- 59096-00 A B-53 157
- B-54 59096-00 A 158
- Set Port Command 159
- B-56 59096-00 A 160
- Set Setup Command 161
- B-60 59096-00 A 164
- 59096-00 A B-61 165
- Show Command 166
- 59096-00 A B-63 167
- 59096-00 A B-69 173
- B-70 59096-00 A 174
- 59096-00 A B-71 175
- B-72 59096-00 A 176
- 59096-00 A B-73 177
- B-74 59096-00 A 178
- 59096-00 A B-75 179
- B-76 59096-00 A 180
- Show Config Command 181
- B-78 59096-00 A 182
- 59096-00 A B-79 183
- B-80 59096-00 A 184
- Show Log Command 185
- B-82 59096-00 A 186
- 59096-00 A B-83 187
- Show Perf Command 188
- 59096-00 A B-85 189
- B-86 59096-00 A 190
- Show Setup Command 191
- B-88 59096-00 A 192
- 59096-00 A B-89 193
- Shutdown Command 194
- Test Command 195
- Uptime Command 198
- User Command 199
- B-96 59096-00 A 200
- 59096-00 A B-97 201
- Whoami Command 202
- Zone Command 203
- B-100 59096-00 A 204
- 59096-00 A B-101 205
- B-102 59096-00 A 206
- Zoneset Command 207
- B-104 59096-00 A 208
- Zoning Command 209
- 59096-00 A B-107 211
- B-108 59096-00 A 212
- 59096-00 A B-109 213
- B-110 59096-00 A 214
- Glossary 215
- Glossary-2 59096-00 A 216
- 59096-00 A Glossary-3 217
- Glossary-4 59096-00 A 218
- 59096-00 A Glossary-5 219
- Glossary-6 59096-00 A 220
- Numerics 221
- Index-2 59096-00 A 222
- Index-3 59096-00 A 223
- Index-4 59096-00 A 224
- Index-5 59096-00 A 225
- Index-6 59096-00 A 226
- 59096-00 A Index-7 227
- Index – Index 228
- Index-8 59096-00 A 228
Manuais e produtos relacionados com Comutadores de rede Qlogic SANbox 5602
Comutadores de rede Qlogic SANbox2-8c Guia de Instalação
(256 páginas)
(256 páginas)
Comutadores de rede Qlogic SANbox2-8c Guia do Utilizador
(218 páginas)
(218 páginas)
Comutadores de rede Qlogic SANbox-8 Manual do Utilizador
(112 páginas)
(112 páginas)
(114 páginas)
Comutadores de rede Qlogic SANbox2-64 Guia de Instalação
(202 páginas)
(202 páginas)
Comutadores de rede Qlogic SANbox2-8c Guia de Instalação
(162 páginas)
(162 páginas)
Panasonic TH37PW5LZ podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Telewizory plazmowe Panasonic TH37PW5LZ.
Dostarczamy 1 pdf podręczników Panasonic TH37PW5LZ do pobrania za darmo według typów dokumentów: Instrukcje Operacyjne
Comentários a estes Manuais