Qlogic SANsurfer iSCSI HBA CLI Guia do Utilizador descarregar pdf (Página 19)

3 – Initial Installation

Installation Instructions

SN0054621-00 B 3-5

5. The Start copying files dialog box displays (see figure 3-4). Read the

information, then click Next.

Figure 3-4. Start Copying Files Dialog Box

6. After the program is installed, the Setup complete dialog box displays. Click

Finish.

Figure 3-5. Setup Complete Dialog Box

7. The following message displays:

SAnsurferiCLI can be executed from a command prompt with the

command "iscli", however you must restart your computer to

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 79 80

User’s Guide 1
Page ii SN0054621-00 B 2
SN0054621-00 B Page iii 3
Table of Contents 5
Page vi SN0054621-00 B 6
SANsurfer iSCSI HBA CLI 7
SN0054621-00 B Page vii 7
Figure Page 8
Table Page 8
Introduction 9
1 – Introduction 10
Technical Support 10
1-2 SN0054621-00 B 10
Getting Started 11
Port Alias: 12
Non-interactive Mode 13
Initial Installation 15
Installation Instructions 17
SN0054621-00 B 3-3 17
3 – Initial Installation 17
3-4 SN0054621-00 B 18
SN0054621-00 B 3-5 19
Red Hat/SuSE Linux/PPC 20
Solaris SPARC/Solaris x86 20
Uninstall Instructions 20
3-8 SN0054621-00 B 22
Interactive Mode Commands 23
HBA Options Menu 24
HBA Network Settings Menu 25
Display Network Settings 25
Configure IP Settings 26
(Command Line Option -ipdhcp) 26
Using DHCP 26
Using SLP 27
(Command Line Option -isns) 27
HBA Firmware Settings Menu 27
(Command Line Option -c) 28
Change HBA Alias Name 36
Edit a Specific HBA Setting 37
Configure iSCSI Settings 37
(Command Line Option -n) 37
Configure Firmware Settings 38
Configure Device Settings 38
Configure Basic Settings 39
Configure Advanced Settings 40
Restore Default HBA Settings 40
(Command Line Option -rdf) 40
4 – Interactive Mode Commands 41
SN0054621-00 B 4-19 41
Display Bootcode Information 42
(Command Line Option -binfo) 42
Set Bootcode Mode 42
SN0054621-00 B 4-21 43
HBA Restore Factory Defaults 44
(Command Line Option -rdh) 44
HBA Information 44
(Command Line Option -pinfo) 44
Reset HBA 45
(Command Line Option -b) 45
Target Menu 46
List Targets 46
(Command Line Option -t) 46
Bind Target 47
(Command Line Option -pb) 47
Unbind Target 47
Configure Target Parameters 47
Add a Target 48
(Command Line Option -pa) 48
Add a CHAP Entry 50
Add a Default BIDI CHAP 50
Edit a CHAP Entry 51
(Command Line Option -edchap) 51
Delete a CHAP Entry 51
List LUN Information 52
(Command Line Option -l) 52
Diagnostic Menu 52
Ping Target 53
(Command Line Option -ping) 53
Perform Loopback Test 53
(Command Line Option -lb) 53
(Command Line Option -rwt) 54
Display HBA Statistics 54
(Command Line Option -stat) 54
SN0054621-00 B 4-33 55
(Command Line Option -vpd) 56
Set Working Adapter 56
Non-interactive Mode Commands 57
■ Host name 59
■ Host version 59
■ Host type 59
(Configure iSCSI Settings) 60
(Perform Loopback Test) 63
-dspchap 64
(Display a CHAP Table) 64
-chapmap 64
(Restore HBA Settings) 67
5-16 SN0054621-00 B 72
Index-8 SN0054621-00 B 80

Comentários a estes Manuais

Sem comentários

Qlogic SANsurfer iSCSI HBA CLI Guia do Utilizador Página 19

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Qlogic SANsurfer iSCSI HBA CLI